Experimental Investigation of Dental Composites Degradation After Early Water Exposure.

While dental composite long-term aging has already been studied in the past, no data exist about the early aging while it might be detrimental regarding the composites' longevity. This study aims to better understand the effects of early water exposure on dental composites. Dental resin composites with different fillers ratio were subjected to water exposure during 24 h, 1 week, or 1 month. After photopolymerization, the samples were stored at different conditions, whether in wet or dry condition (W, D, respectively) and in wet conditions after a first 24 h storage in dry conditions (DW). Three-point bending tests were performed to measure the flexural modulus. The samples were then subjected to a sorption/desorption protocol. While the matrix alone did not undergo any mechanical degradation with exposure time, the composites matrices presented a decrease in elastic modulus. This decrease was the highest for the matrix with nonsilanized fillers. Interestingly, the DW condition was detrimental for all the samples. Regarding the sample with nonsilanized fillers in DW for 1 month presented an elastic modulus lower than the matrix alone. These results were assigned to the sorption capacity of the polymer matrix, suggesting that the diffusion mechanisms and the nature of water molecules are determinant in the composite degradation. This study showed that dental composite early degradation mechanisms after water exposure are involved in the polymer matrix postpolymerization process as soon as after 24 h. Such mechanisms are detrimental in terms of the dental composite efficiency and have to be understood.

A numerical, theoretical and experimental study of the effect of thermocycling on the matrix-filler interface of dental restorative materials.

OBJECTIVE: Thermocycling is widely used to age dental composites but with very different results from one study to another, even with apparent similar conditions. This study aims at understanding better the relative damaging speed of matrix and fillers, based on theoretical models. METHODS: Eight formulations of an experimental dental material were produced. The same organic matrix was used and silanated barium glass particles were added as fillers with different filler ratios. Samples were thermocycled up to 10 000 cycles. Three-point bending tests were carried out at different steps. The yield stress was measured among other mechanical properties. RESULTS: Composite properties were degraded by thermocycling. The decrease was slight during the first 5 000 cycles whereas it decreased significantly after 10 000 cycles. The Turcsányi model asserts that the interface yield stress is slightly affected in the first 5 000 cycles and then falls down, while the decrease of matrix yield stress is linear. SIGNIFICANCE: Each component of a composite does not age at the same rate. First, the matrix acts as a protector until the water finds its way to the interphase. The filler silanization treatment is highly sensitive to hydrolysis and is damaged rapidly from that moment. Numerical simulations and surface observations confirmed that cracks appear to propagate in the neighbourhood of the interface but not directly within it.

Theoretical prediction of dental composites yield stress and flexural modulus based on filler volume ratio.

OBJECTIVE: A costly advantageous approach in composites development process is to limit experimental tests by predicting mechanical properties with respect to their filler ratio. Models exist for other fields than dentistry. They have been compared to 3-point bending test experimental results for yield stress, flexural modulus and flexural strength. METHODS: Five formulations of the same experimental material were made. They were composed of an organic matrix and different ratios of silanated barium glass particles. The samples were stored in distilled water for 24h at 37°C prior to the 3-point bending test. The Turcsányi model for yield stress was notably investigated, and SEM was used to complete data analysis. RESULTS: The yield stress showed reproducible results and a good fit with Turcsányi model with respect to filler ratio. The flexural modulus data are not scattered but did not fit with the existing models. No trend could emerge for flexural strength and strain because of scattering; these properties are more unpredictable. The SEM observations of fracture areas confirm a good matrix-filler interface quality. SIGNIFICANCE: SEM pictures validated the numerical parameter obtained from Turcsányi model. The latter therefore seems to be applicable to dental composites. Firstly, it enables to predict the evolution of the material yield stress without testing all filler ratios. Secondly, this model provides a good way to get micro-information on the matrix-filler interface from macroscopic tests. The discrepancy between flexural modulus results and theory highlighted the necessity to include an "interface quality" parameter in accurate predictive models.

Nd:YAP laser in the treatment of dentinal hypersensitivity: An ex vivo study.

PURPOSE: The aims of this ex vivo study were to evaluate the effectiveness of the Nd:YAP laser in the treatment of dentin hypersensitivity, to compare the temperature rise during laser irradiation at three different dentine thicknesses, and to analyse the composition of the dentine-lased surface. METHODS: A total of 33 teeth were used in this study. For scanning electron microscopy (SEM) observation, 24 teeth were transversely sectioned and divided into 4 groups: group A was irrigated with EDTA; group B was irradiated by Nd:YAP laser with 180 mJ energy/per pulse, 0.9 W average power, and 5 Hz frequency (power density [PD] = 229 W/cm2); group C was irradiated by Nd:YAP laser with 280 mJ energy/pulse, 1.4 W average power, and 5 Hz frequency (PD = 356 W/cm2); and group D was irradiated by Nd:YAP with 360 mJ energy/pulse, 1.8 W average power, and 5 Hz frequency (PD = 458 W/cm2). Energy-dispersive spectroscopy (EDS) analysis was performed on the same teeth evaluated for SEM observations. For temperature increase evaluation performed with thermocouples, 9 teeth were transversely sectioned at 3 different thicknesses (3 for each group) of 1, 2, and 3 mm. RESULTS: Statistical analysis showed significant changes in the diameter of the dentinal tubule orifices among all groups; EDS did not show modification of the Ca/P ratio. Temperature increase under irradiation exceeded 5.5 °C only in the group D samples. CONCLUSIONS: This ex vivo study, based on temperature recording, SEM observation, and EDS analysis, demonstrated that Nd:YAP laser at a PD of 356 W/cm2, corresponding to an average power of 1.4 W, defines the best treatment for dentine hypersensitivity in terms of compromise between efficacy of the treatment and safety of the pulp.

Finishing and polishing effects of multiblade burs on the surface texture of 5 resin composites: microhardness and roughness testing.

OBJECTIVES: The aim of this in vitro study was to test the effect of 2 finishing-polishing sequences (QB, combining a 12/15-fluted finishing bur and an EVO-Light polisher; QWB, adding a 30-fluted polishing bur after the 12/15-fluted finishing bur used in the QB sequence) on 5 nanotech-based resin composites (Filtek Z500, Ceram X Mono, Ceram X Duo, Tetric Evoceram, and Tetric Evoceram Bulk Fill) by comparing their final surface roughness and hardness values to those of a Mylar strip control group (MS). MATERIALS AND METHODS: Twelve specimens of each nanocomposite were prepared in Teflon moulds. The surface of each resin composite was finished with QB (5 samples), QWB (5 samples), or MS (2 samples), and then evaluated (60 samples). Roughness was analysed with an optical profilometer, microhardness was tested with a Vickers indenter, and the surfaces were examined by optical and scanning electron microscopy. Data were analysed using the Kruskal-Wallis test (p < 0.05) followed by the Dunn test. RESULTS: For the hardness and roughness of nanocomposite resin, the QWB sequence was significantly more effective than QB (p < 0.05). The Filtek Z500 showed significantly harder surfaces regardless of the finishing-polishing sequence (p < 0.05). CONCLUSIONS: QWB yielded the best values of surface roughness and hardness. The hardness and roughness of the 5 nanocomposites presented less significant differences when QWB was used.

CO2 laser dentin surface treatment most effectively increased ceramic shear bond strength.

BACKGROUND AND AIMS: The purpose of this study is to determine the effect of CO2 laser irradiation in comparison with sandblasting (Sb), hydrofluoric acid (Hf) and silane coupling agent (Si) on shear bond strength (SBS) of resin cement to CAD/CAM ceramics bonded to dentin. MATERIAL AND METHODS: Forty-eight (CAD/CAM) ceramic discs were prepared and grouped by material, i.e. lithium disilicate (Emax CAD) and zirconia ceramic (Emax ZirCAD), distributed into four different groups: group A, lithium disilicate (Li) CO2/HF/Si; group B, Li: HF/Si; group C, zirconia (Zr) CO2/Sb/Si; group D, Zr: Sb/Si. RESULTS: It was shown significant difference between irradiated and non-irradiated groups in terms of shear bond strength for zirconia ceramics (p value = 0.039). CONCLUSION: CO2 laser irradiation increases shear bond strength for both CAD/CAM ceramics bonded to dentin.

Disilicate Dental Ceramic Surface Preparation by 1070 nm Fiber Laser: Thermal and Ultrastructural Analysis.

Lithium disilicate dental ceramic bonding, realized by using different resins, is strictly dependent on micro-mechanical retention and chemical adhesion. The aim of this in vitro study was to investigate the capability of a 1070 nm fiber laser for their surface treatment. Samples were irradiated by a pulsed fiber laser at 1070 nm with different parameters (peak power of 5, 7.5 and 10 kW, repetition rate (RR) 20 kHz, speed of 10 and 50 mm/s, and total energy density from 1.3 to 27 kW/cm²) and the thermal elevation during the experiment was recorded by a fiber Bragg grating (FBG) temperature sensor. Subsequently, the surface modifications were analyzed by optical microscope, scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDS). With a peak power of 5 kW, RR of 20 kHz, and speed of 50 mm/s, the microscopic observation of the irradiated surface showed increased roughness with small areas of melting and carbonization. EDS analysis revealed that, with these parameters, there are no evident differences between laser-processed samples and controls. Thermal elevation during laser irradiation ranged between 5 °C and 9 °C. A 1070 nm fiber laser can be considered as a good device to increase the adhesion of lithium disilicate ceramics when optimum parameters are considered.

Microhardness evaluations of CAD/CAM ceramics irradiated with CO2 or Nd:YAP laser.

BACKGROUND AND AIMS: The aim of this study was to measure the microhardness values of irradiated computer-aided design/computer-aided manufacturing (CAD/CAM) ceramics surfaces before and after thermal treatment. MATERIALS AND METHODS: Sixty CAD/CAM ceramic discs were prepared and grouped by material, i.e. lithium disilicate ceramic (Emax CAD) and zirconia ceramic (Emax ZirCAD). Laser irradiation at the material surface was performed with a carbon dioxide laser at 5 Watt (W) or 10 W power in continuous mode (CW mode), or with a neodymium:yttrium aluminum perovskite (Nd:YAP) laser at 10 W on graphite and non-graphite surfaces. Vickers hardness was tested at 0.3 kgf for lithium disilicate and 1 kgf for zirconia. RESULTS: Emax CAD irradiated with CO2 at 5 W increased microhardness by 6.32 GPa whereas Emax ZirCAD irradiated with Nd:YAP decreased microhardness by 17.46 GPa. CONCLUSION: CO2 laser effectively increases the microhardness of lithium disilicate ceramics (Emax CAD).

Shear bond, wettability and AFM evaluations on CO2 laser-irradiated CAD/CAM ceramic surfaces.

The purpose of this study is to determine the CO2 laser irradiation in comparison with sandblasting (Sb), hydrofluoric acid (Hf) and silane coupling agent (Si) on shear bond strength (SBS), roughness (Rg) and wettability (Wt) of resin cement to CAD/CAM ceramics. Sixty (CAD/CAM) ceramic discs were prepared and distributed into six different groups: group A, control lithium disilicate (Li); group B, control zirconia (Zr); group C, Li: CO2/HF/Si; group D, Li: HF/Si; group E, Zr: CO2/Sb/Si; group F, Zr: Sb/Si. Result showed significant difference between irradiated and non-irradiated in terms of shear bond strength for zirconia ceramics (p value = 0.014). Moreover, partial surface wettability for irradiated and non-irradiated ceramics. Irradiated surface demonstrated more rough surface in lithium disilicate than zirconia ceramics. CO2 irradiation could increase shear bond strength, surface roughness and wettability for both CAD/CAM ceramics.

The effect of CO2 and Nd:YAP lasers on CAD/CAM Ceramics: SEM, EDS and thermal studies.

BACKGROUND AND AIMS: The objective of this study was to investigate the interaction of infrared laser light on Computer Aided Design and Computer Aided Manufacturing (CAD/CAM) ceramic surfaces. MATERIAL AND METHODS: Sixty CAD/CAM ceramic discs were prepared and divided into two different groups: lithiumdisilicate ceramic (IPSe.maxCADs) and Zirconia ceramic (IPSe.maxZirCADs). The laser irradiation was performed on graphite and non-graphite surfaces with a Carbon Dioxide laser at 5W and 10W power in continuous mode (CW mode) and with Neodymium Yttrium Aluminum Perovskite (Nd:YAP) laser at 10W. Surface textures and compositions were examined using Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS). Thermal elevation was measured by thermocouple during laser irradiation. RESULTS: The SEM observation showed a rough surface plus cracks and fissures on CO2 10W samples and melting areas in Nd:YAP samples; moreover, with CO2 5W smooth and shallow surfaces were observed. EDS analysis revealed that laser irradiation does not result in modifications of the chemical composition even if minor changes in the atomic mass percentage of the components were registered. Thermocouple showed several thermal changes during laser irradiation. CONCLUSION: CO2 and Nd:YAP lasers modify CAD/CAM ceramic surface without chemical composition modifications.

Photodynamic therapy versus ultrasonic irrigation: interaction with endodontic microbial biofilm, an ex vivo study.

INTRODUCTION: Photodynamic therapy was introduced as an adjuvant to conventional chemo-mechanical debridement during endodontic treatment to overcome the persistence of biofilms. The aim of this study was to evaluate the ability of photodynamic therapy (PDT) to disrupt an experimental microbial biofilm inside the root canal in a clinically applicable working time. MATERIALS AND METHODS: Thirty extracted teeth were prepared and then divided in three groups. All samples were infected with an artificially formed biofilm made of Enterococcus faecalis, Streptococcus salivarius, Porphyromonas gingivalis and Prevotella intermedia bacteria. First group was treated with Aseptim Plus® photo-activated (LED) disinfection system, second group by a 650 nm Diode Laser and Toluidine blue as photosensitizer, and the third group, as control group, by ultrasonic irrigation (PUI) using EDTA 17% and NaOCl 2.6% solutions. The working time for all three groups was fixed at 3 min. Presence or absence of biofilm was assessed by aerobic and anaerobic cultures. RESULTS: There was no statistically significant difference between results obtained from groups treated by Aseptim Plus® and Diode Laser (P<0.6267). In cultures of both groups there was a maximal bacterial growth. The group that was treated by ultrasonic irrigation and NaOCl and EDTA solutions had the best results (P<0.0001): there was a statistically significant reduction of bacterial load and destruction of microbial biofilm. CONCLUSION: Under the condition of this study, Photodynamic therapy could not disrupt endodontic artificial microbial biofilm and could not inhibit bacterial growth in a clinically favorable working time.